Categories
Uncategorized

cisco air-lap1142n-a-k9 default login .com Sign In Online Support Customer Service

A useful knowledge is that now when you register an account on a popular website, the system will automatically compare it with the publicly leaked password. If it matches, the system will prompt you. For those who already have an account, you need to pay attention to the risk warning given by the system and change the password in time.

Cisco AIR-LAP1142N-A-K9 Default Router Login and Password

https://www.cleancss.com/router-default/Cisco/AIR-LAP1142N-A-K9

11 rows · Find the default login, username, password, and ip address for your Cisco AIR-LAP1142N-A-K9 router. You will need to know then when you get a new router, or when you reset your router.

AIR-LAP1142N-A-K9 factory reset – Cisco Community

https://community.cisco.com/t5/wireless/air

Aug 20, 2014 · I have the same problem I have the AIR-LAP1142N-E-K9. I have managed to Get default username and password (Cisco/Cisco) However I am unable to reset using SSH. When I run clear ap config I just get the following. AP#clear ap config ^ % Invalid input detected at ‘^’ marker. To make matters worse I can not access the GUI via HTTP

https://toviladul.weebly.com/uploads/1/3/0/7/130776498/xaxuxonoxok.pdf

Air lap1142n a k9 reset to default Cisco Access Point (AIRLAP1142N-S-K9) Power on the Cisco Access Point and press the mode button to reset the previous setting then connect the console cable rj-45 end to the AP and usb end to the laptop. For its configuration we need two things.

Cisco access point air-lap1142n-a-k9 factory reset …

https://refurbdevice.blogspot.com/2017/07/cisco

Cisco access point air-lap1142n-a-k9 factory reset. Biren Patel 1:28 PM. Step 1: Use PoE switch to power on Cisco access point (P/N: air-lap1142n-a-k9) Step 2: Enter user name and password as below (Case sensitive) User: Cisco. Password: Cisco. Step 3: Enter command line as below to reset the device to factory default.

How to configure the Cisco Access Point (AIR-LAP1142N-S-K9)

https://greenwhitehat.blogspot.com/2017/08/how-to…

Aug 16, 2017 · How to configure the Cisco Access Point (AIR-LAP1142N-S-K9) Power on the Cisco Access Point and press the mode button to reset the previous setting then connect the console cable rj-45 end to the AP and usb end to the laptop. For its configuration we need two things.

Solved: Cisco AIR-LAP1252AG-A-K9 Factory Reset – Cisco …

https://community.cisco.com/t5/switching/ciscoair

cisco AIR-LAP1252AG-A-K9 (PowerPC 8349) processor (revision A0) with 49142K/16. 384K bytes of memory. Processor board ID FTX123590E6. PowerPC 8349 CPU at 533Mhz, revision number 0x0031. Last …

AIR-LAP1142N-A-K9 Lightweight to Standalone AP Mode – Cisco

https://community.cisco.com/t5/wireless/air

Jul 26, 2019 · AIR-LAP1142N-A-K9 Lightweight to Standalone AP Mode. Helllo! I work for a small IT firm, and we currently do not have any service agreement with Cisco. We have about a dozen of these LAP1142 access points on a network that no longer has its wifi controller, so I have been searching for ways to revert the AP’s to their standalone mode.

Solved: Cisco AIR-LAP1142N-A-K9 keeps rebooting / loop …

https://community.cisco.com/t5/wireless/ciscoair

Dec 19, 2013 · Cisco AIR-LAP1142N-A-K9 keeps rebooting / loop Hello, I have a Cisco AIR-LAP1142N-A-K9 that keeps rebooting, I’ve done the factory reset (hold the mode button for 20-30 seconds until LED is red). 100+ other APs are up and running fine.

Upgrade 1142 from LWAP to Autonomous – Cisco Community

https://community.cisco.com/t5/wireless-mobility…

Sep 05, 2010 · I decided to upgrade a new Cisco AIR-LAP1142N-A-K9 from the factory lightweight image to an autonomous image so I can have a standalone AP in the event my WLC takes a dive. A buddy of mine asked me to post some instructions for him, so here it is. I completed this in just a few minutes, so this isn’t a big deal.

Leave a Reply

Your email address will not be published.